Bryston SP2 Manuel d'utilisateur télécharger pdf (Page 10)

SP2 Remote Control continued...

1: SOURCE SELECT BUTTONS

These buttons are used to select the desired

source. TV/SAT, DVD, CD, AUX, VCR, and TAPE

function exactly like their corresponding buttons on

the SP2 front panel.

2: BYPASS BUTTONS

To use the 5.1 channel analog input, press the 6CH

BYPASS button. To go back to the previous select-

ed source, press the 6CH BYPASS button again.

To use the Stereo Bypass mode for the currently

selected source, press the 2CH BYPASS button. To

go back to the previous selected mode, press the

2CH BYPASS button again.

3: MODE SELECT BUTTONS

These buttons (THX, SURR, DIG, STEREO, MODE)

are used to change the SP2 decoding mode, and

function exactly like their equivalent buttons on the

front panel.

4: MUTE BUTTON

Pressing this button will fully mute the output of

the SP2.

5: VOLUME/TRIM BUTTONS

These buttons increase and decrease the master

volume. When the SP2 is in its Test/Noise mode,

these buttons are used to adjust the level trim for

each individual speaker.

6: TEST BUTTON

If pressed for more than 3 seconds, the SP2 will

enter the Test/Noise mode. Please see Page 18 for

more details on this mode.

7: POwER BUTTON

Pressing this button will toggle the SP2 in and out

of the Standby power mode.

Installers: please contact Bryston technical support

for information about Discrete On/Off control.

8: SAVE BUTTON

Pressing this button will memorize settings for the

current input, as described in “Saved Settings per

Source” on page 19.

9: DTS BUTTON

Pressing this button toggles between the DTS

Music mode, and the DTS Movie mode. These

modes are used ONLY when a DTS bitstream is

detected. The DTS Music mode is optimized to

provide proper playback of DTS encoded musical

material from DVD, LD or CD sources. DTS Movie

is available for playback of DTS encoded motion

picture soundtracks from DVD or LD sources. Each

mode has an optimized bass management setting

in accordance with the DTS program material.

10: DOLBY BUTTON

Pressing this button will engage the Dolby PLII

Film mode for any 2 channel sources (PCM, Dolby

Digital, or Analog).

11: SETUP BUTTONS

These include SUB, CENTER, OSD, REAR, BACK,

SELECT and MENU/UP/DOWN.

All of these setup functions can be accessed while

listening to movies or music.

SELECT,  and  buttons function like their

corresponding buttons on the SP2 front panel

(= and =). To enter the menu mode,

press any one of these buttons. If OSD is ON,

you will see the menu on your video monitor.

OSD (On-Screen Display) Button will toggle

the OSD function on and off, on your video

monitor, if you are using the Bryston video

switcher.

SUB button will engage the menu for the vol-

ume trim level of the subwoofer channel. Use

the MENU/UP/DOWN button to change the

subwoofer channel level up or down. Press

SELECT when finished.

CENTER button will engage the menu for the

volume trim level of the center channel. Use

the MENU/UP/DOWN button to change the

center channel level up or down. Press SELECT

when finished.

REAR button will engage the menu for the

volume trim level of the rear channels. Use

the MENU/UP/DOWN button to change the rear

channel levels up or down. Press SELECT when

finished.

BACK button will engage the menu for the vol-

ume trim level of the back channels. Use the

MENU/UP/DOWN button to change the back

channel level(s) up or down. Press SELECT

when finished.

12: STATUS LED

Indicates remote control status while accessing

discrete/hidden functions, and changing remote

options. Contact the factory for details.

13: PHOTO SENSOR

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 19 20

Commentaires sur ces manuels

Pas de commentaire

Bryston SP2 Manuel d'utilisateur Page 10

Commentaires sur ces manuels