Bryston SP2 Manuel d'utilisateur télécharger pdf (Page 4)

INTRODUCTION

Congratulations on your purchase of the Bryston

SP2 pre-amplifier/processor. This product will pro-

vide you with the finest available signal control and

DSP audio processing available. Like all Bryston

products the SP2 has been carefully designed and

engineered to deliver a lifetime of enjoyment.

The SP2 offers both pre-amplifier and digi-

tal decoding functions, and it is very important

that you thoroughly read this manual BEFORE you

install and use the SP2.

UNPACKING

Your SP2 was carefully packed at the factory to

protect against any damage in shipping and han-

dling. Carefully examine the packing and the unit

for any signs of external damage or impact and

report those to your dealer or Bryston prior to

using the unit.

Bryston advises that you keep all packaging

in the event that the unit may have to be returned

for service.

ACCESSORIES

In the carton you should have found the following

accessories in addition to the SP2:

1 Bryston SP2 Instruction Manual

1 IEC standard power cord

1 SP2 Infrared Remote Control unit with

backlight and battery installed

SAFETY

It is VERY IMPORTANT that you read and complete-

ly understand the safety instructions and warning

on page one of this manual before installing or con-

necting the SP2 to any electrical power source.

NEw FEATURES

• New “C” series cosmetics

• RS-232 software updates

• DSP firmware updates via SPDIF

• New Texas Instruments Aureus Audio DSP chip

• Seven times greater processing power

• DTS 96/24 5.1 surround decoding

• Dolby 96/24 two channel surround PLIIx

decoding

• Four independent hi-pass subwoofer crossover

points:

   ◊ FrontLeft/Right

   ◊ Centre

   ◊ Left/Rightsurrounds

   ◊ BackLeft/Right

• 7.1 decoding from 2 channel source in Dolby

PLIIx Music and Film modes

• 7.1 decoding from 2 channel source in DTS

Neo-6 Music & Cinema modes

• 7.1 surround effects decoding from 2 channel

digital sources

• 7.1 Surround effects decoding from 2 channel

analog sources

• 96/24 Stereo decoding

• 96/24 DTS 5.1 decoding

• 96/24 Matrix surround modes in 5.1

• 9Dynamic range adjustment per individual

input

• New, faster micro-controller

• New THX modes: Cinema, THX Music Mode,

THX Games Mode

• new THX ULTRA sub-woofer setting

POwER INLET & SwITCH

Located on the right hand side of the

rear panel, adjacent to the IEC power

cord socket is a large computer-style

switch that controls the main electrical

power to the unit. This is the ONLY

switch that actually completely turns

off all power to the unit. When the SP2

is connected to an appropriate AC

power source, and the power switch is switched to

the ‘I’ position, the unit automatically sets itself

into a STANDBY power mode, where-in only the

minimum necessary circuitry to respond to the

remote control’s power-on command or the

momentary push-button power switch on the front

panel are active. The RED standby LED on the

front panel illuminates.

Pressing the momentary POWER bush-button

switch on the front panel or the POWER button on

the remote immediately takes the unit out of its

STANDBY mode into its normal operating mode.

This is indicated by the illumination of the front

panel LCD display, the illumination of the LED cor-

responding to the source you last selected, and the

units LED operating mode indicators.

NOTE:

If your unit’s LCD backlight does not illuminate

when the SP2 is plugged into an operating out-

let, and switched out of STANDBY mode, please

check to see that the rear panel main power switch

{mains switch} is in the ON position.

If the SP2 is to be unused for an extended

period of time (i.e. a vacation) it is strongly recom-

mended that it be turned off using the main power

switch on the back panel.

1 2 3 4 5 6 7 8 9 ... 19 20

Commentaires sur ces manuels

Pas de commentaire

Bryston SP2 Manuel d'utilisateur Page 4

Commentaires sur ces manuels